Home Technology Semiconductor radio

Semiconductor radio



A synonym for semiconductor radio generally refers to transistor radio

Brief description

Transistor radio is a small transistor-based radio receiver. Historically, "transistor radio" specifically refers to a monophonic AM radio with a frequency of 540 to 1 600 kilohertz.

The first civilian transistor radio was developed by the Society of Industrial Development Engineers in Indianapolis, Indiana. The price was US$49.95 and approximately 150,000 units were sold. It wasn't until 1960 that transistor radios entered ordinary households with some models falling to $20. The influx of products from Hong Kong made the price drop below $10.

The transistor radio is the second generation radio after the tube radio. Compared with electronic tubes, transistors are small in size, light in weight, resistant to vibration, long-lived, and consume less power. Radios can be made compact and have relatively stable performance. Therefore, after the advent of transistor radios, a large number of portable radios and pocket radios have emerged, bringing people It's very convenient.

With the emergence and development of integrated circuits, transistors have been replaced by integrated circuits, and the third generation of radios-integrated circuit radios, sometimes also known as semiconductor radios.

After the radio uses integrated circuits, not only the volume can be made smaller, but also the reliability is high. As the number of integrated circuit components is getting larger and larger, radios made with it have better performance and more functions. The integration of radios has become an inevitable trend.

Principle

The antenna receives the high-frequency amplitude modulation wave (AM) signal transmitted by many broadcasting stations, selects the required station signal through the same input channel, and sends it to the frequency conversion After frequency conversion, it outputs an intermediate frequency signal with a frequency of 465 kHz and sends it to an intermediate frequency selective amplifier for amplification. The amplified intermediate frequency signal is then sent to a detector for detection and restored to an audio signal. The audio signal is then passed through the pre-low frequency amplifier It is amplified with the final power amplifier and sent to the speaker, and the audio signal is restored to sound by the speaker.

In order to improve the performance of the radio, an AGC circuit is also added. The superheterodyne radio is a receiver with better performance, which has the advantages of high sensitivity and good selectivity.

Classification

1. According to the shape and size, there are pocket radios and portable radios. The pocket green harvesting machine can be divided into toy type, thin type and ultra-thin type. The volume of this type of transistor radio is generally between 100 and 700 cubic centimeters. Portable transistor radios can be divided into small portable, medium portable and large portable. The volume of this type of radio is generally between 700 and 5000 cubic centimeters.

2. According to the purpose. There is an ordinary radio (only radio programs can be listened to). Clock-controlled radio, car radio, radio and telephone, multi-purpose machine for receiving, amplifying, singing, and intercom, and special information broadcasting radio, etc.

3. According to the modulation method and the number of bands: there are FM radio, AM radio, single band, multi-band (also called full-band radio, etc.).

People are used to calling radios with medium wave, short wave, FM wave (ultrashort wave), and some long wave and microwave bands as full-band radios.

The performance of the full-band radio generally reaches the extreme or first-class radio level. It has the advantages of high sensitivity, good selectivity, low distortion and high output power. Most full-band radios can receive stereo broadcasts.

4. Classified by circuit category: There are two types of regenerative radios and superheterodyne radios. Due to the low quality indicators of regenerative radios, some complete machine manufacturers no longer assemble and produce them. The more popular is the superheterodyne radio. In the superheterodyne radio, according to different electroacoustic performance indicators, it can be divided into special grade, first grade, second grade, third grade and fourth grade radio.

5. According to the components used: a radio assembled by a single resistor, capacitor, diode, triode and other components is generally called a radio assembled with discrete components. Radios assembled with integrated circuits are called integrated circuit radios. In terms of circuit structure, integrated circuit radios can be divided into monolithic, multi-chip, hybrid and thick and thin film types. There are also radios assembled with germanium tubes and silicon tubes, and radios assembled with silicon-germanium mixed use.

6. In terms of working voltage: Generally, radios with a power supply below 3 volts are collectively referred to as low-voltage radios, which have the advantages of saving electricity and easy to use.

Shopping

To choose a good transistor radio, you must first understand four basic relationships:

1. The larger the size of the case, the better the sound quality;

2. The larger the horn diameter, the better the sound quality;

3. The larger the battery volume, the longer the relative service life of the battery;

4. The longer the magnet, the higher the sensitivity (more stations).

Secondly, five points should be paid attention to when purchasing:

1. The change after the power supply voltage is reduced should be small. When selecting, you can bring a half-new and half-used battery for trial listening, and the impact on a high-quality radio should not be significant.

2. The distortion of the deviation tuning station should be small. After finding a radio station, the left and right adjustments should be biased, the distortion should be small, and there should be no whistling sound, otherwise, the frequency characteristics of the intermediate frequency part are poor.

3. The volume change should be small when turning the direction.

4. Human body induction affects little. When a person's body is close to the radio, it will have a certain impact on the work of the radio. This situation is particularly obvious for shortwave.

5. The noise should be low. Noise generally includes electrical noise and mechanical noise. Turn the radio to a place where there is no station, and turn on the volume to the maximum. At this time, the minimum sound is better. Listen to a program and listen to whether there are noises caused by resonance of certain components when the volume is loud.

Finally, you should also pay attention to whether the tuning knobs and buttons are coordinated and effective, whether the hand feel is good, whether the shell of the radio is damaged, etc.

Use and maintenance

1. When listening to the radio, first turn on the power switch or turn the volume knob to hear a sound, indicating that the power is on. Then, turn the volume knob to the appropriate position. Then, turn the tuning knob to find the station you want to listen to, and then turn it back and forth carefully to make the sound realistic and pleasant. If you listen to shortwave or FM radio, pull out the whip antenna, close the band (or channel) switch, and turn the fine-tuning knob to tune the radio station after carefully turning the tuning knob. When not listening, turn off the power switch, or turn the volume knob in the opposite direction to cut off the power.

2. The magnetic antenna in the transistor radio has a strong directivity. When receiving remote stations, pay attention to turning the direction of the radio to make the received signal the strongest.

3. The beam stage of the transistor radio mostly uses a Class B push-pull power amplifier circuit. The characteristic of this circuit is that the louder the volume, the higher the power consumption. To prolong the service life of the battery, the volume should not be too high when listening. In addition, the volume is too loud, exceeding the undistorted output power of the radio, and the sound is also awkward.

4. The volume of the transistor radio becomes smaller or the sound quality deteriorates. It is likely that the battery is almost used. Replace with a new battery in time to prevent the liquid in the battery from flowing out and corroding the battery card. When replacing the battery, pay attention to the installation direction, do not put it down, so as not to damage the components.

5. When the transistor radio is not in use, it should be placed in a cool and ventilated place, not exposed to the sun, damp, violently shaken, and do not put it outside to listen in the cold winter.

6. After a transistor radio (especially a desktop radio) is used for a period of time, dust will accumulate inside. Dust accumulates inside. You can open the back cover and gently clean it with a soft brush. Don't wipe it with a wet cloth, or it will rust the metal parts.

This article is from the network, does not represent the position of this station. Please indicate the origin of reprint
TOP